Tool Kits

MPTK130EK

Cushion grip body. Six position speed dial. Spindle lock button. Fitted with a quick change collet nut system. Ideal for a wide range of smaller DIY and craft jobs as an alternative to larger power tools. Supplied in a fitted aluminium case.

 

Specifications:

 

• Nominal voltage: 230v~50 Hz.

• Power input: 130W.

• No load speed: 8,000-30,000rpm.

• Noise: 82db(A). Weight: 640g.

 

Accessories included: Flexible drive shaft. Flexible rubber drive shaft for use where maximum flexibility is required, to improve access in confined spaces. Bench clamp and tool steady. Fix the tool steady to a work bench or table to hold the multi-tool in place when using the flexible drive shaft. 118 Piece accessory kit includes: various collets, cutters, drills, abrasives, brushes, burrs, wheels, discs of mandrels. Bench clamp and tool steady To fix tool steady to a work bench or table to hold the multi tool in place when using the flexible drive shaft.

F05003MK

Uses 2”and 3” backing pads. Rubber handle provides grip and operator comfort. Two finger throttle for easier control and less fatigue. Adjustable power regulator to match the speed to the job. Ball bearing construction for a long tool life. Accessories included: 2” and 3” backing pads. 10 x 2” dia. Sanding discs – 320, 400 and 600 grit. 10 x 3” dia sanding discs - 320, 400 and 600 grit. Spindle key and instructions. Supplied in a robust blow-moulded carry case.

 

• Air inlet thread: 1/4” NPT.

• Minimum air hose size (ID): 3/8” (10mm).

• Air pressure: 90PSI/6.3Bar.

• Air consumption: 4CFM* (144 ltr/min).

• Vibration level: 0.9 m/s2.

 

 

*Based on a 15 second cycle per minute average use.

Multi-purpose kit containing: one of each of the following surface preparation discs: fine, medium and coarse. 2x abrasive disc grades: P36, P60, P80 and P120. 1x 6mm diameter shank to fit the backing pad. Supplied in a sturdy plastic carry case.

 

• Air inlet thread: 1/4” NPT.

• Minimum air hose size (ID): 3/8” (10mm).

• Air pressure: 90PSI/6.3Bar.

• Air consumption: 4CFM* (144 ltr/min).

 

*Based on a 15 second cycle per minute average use.

 

For repairing dents in body panels. Supplied complete with self tapping pull screw for use where access to the rear of the panel is blocked by reinforcements or other parts, a range of steel hooks and pull curls for pulling the edges of panels and a chain and hook. The long hammer shaft allows the pulling/striking force to be precisely controlled. 

 

Contents: (1x) hammer (10lbs cast iron), 22.5Ø x 500 and 22.5Ø x 200mm pipes, 2 hole pipes, 6 x 170, 6 x 120, 6 x 200 and 3mm x 100mm plates, chain and hook, hex nut and blow moulded storage case.

Winds back disc brake calipers when replacing brake pads. Professional quality, allows the easy return of brake piston into the caliper. Suitable for most braking systems.

Long Handled Gasket Scraper Set


For cleaning cylinder heads and removing old sealants and carbon build up. Hardened and tempered carbon steel shanks and heads are ‘offset to edge’ to allow easy scraping of flat surfaces. Simple ‘firmer’ style bevelled points with longer head lengths allow for scrapers to be re-ground several times for maximum service life. Impact resistant square section handle for secure grip even when greasy.


Set includes blade widths:

 

• 19mm (3/4”),
• 25mm (1”) and
• 38mm (11/2”).

Overall length:

• 280mm (11")

Standard Length Gasket Scraper Set

Rigid carbon scrapers ideal for cleaning cylinder heads, removing old sealants, carbon build up and a variety of general mutipurpose automotive applications.


Set includes blade lengths:

205mm x 13mm (8” x 1/2”), 205mm x 25mm (8” x 1"), 93mm x 25mm (31/2" x 1”), 97mm x 15mm (33/4” x 5/8”).