Automotive Tool

For use in hand lift applications only. Multiple vacuums used on a single load can only improve handling. If using more than one vacuum tool the ratio of maximum lift capacity does not increase.


To lift heavier weights a larger vacuum must be used. All are fitted with a rubber suction cap which will not damage contact surface during the lifting action. For use on glass and plastic or any smooth surface material and can also beused for pulling out dents.

Suitable for cutting holes in steel metal, steel, plastic and brass. The hardened steel cutter is reversible increasing tool life. adjusting the spring loaded centre point, screw accurately controls the depth of cut. Allowing the top to be removed whilst leaving the lower panel in place.

Lightweight tubular steel design with chain stops foam protection and rubber ffet. Large rubber suckers prevent screen from moving during preparation.

Folding frame makes this ideal for both workshop and mobile screen preparation.

Rugged construction with a heavy duty return spring. Chrome plated piston inhibits rusting. 1/4 NPT thread size. Accessories easily snap on.

Single man operated pneumatic bleeder which simplifies the bleeding of hydraulic fluid in vehicle clutches and brake systems, also used for the collection of other non-corrosive fluid spillage. Has a 1ltr container with a ¼” NPT connection, operates from 90 - 145psi (6 - 10bar) air pressure with an air consumption rate of 180ltr/min, an extraction rate of 1.6ltr/min and vacuum (max) of 550mm HG.

Handles non-flammable liquids between 0 and 80°C.

Designed for the pressure testing of cooling systems and radiator caps up to 35psi (2.5 bar). Suitable for use on most makes of car and commercial vehicles, including: Mercedes, Ford, Chrysler, Peugeot, Honda, Lexus, Mazda, Suzuki, Toyota, Nissan, Opel, Volkswagen, Saab, Volvo, Audi, Citroen, Fiat and BMW.


Contents: 14 radiator pressure testing caps, for use in testing cooling systems for leaks. Two cap adaptors, sizes 2 - 3 and 4 - 5, for testing radiator cap release pressure and seal condition. Two 200psi coolant hoses (5/16” and 3/8”), for use with T-adaptor for in-line pressure testing. T- adaptor for creating in-line pressure testing set-up. Two 3/4” hose clips.

Vacuum testing kit  and Brake Bleeding Kit that helps to locate and identify faults on cars, motorcycles and commercial vehicles. Supplied in robust blow moulded case.

Contents: serviceable metal bodied vacuum pump, reservoir jar, transfer lid, storage lid, 4x lengths of 6mm ID tubing, 1x length of 4mm ID tubing adaptor. Set of brake bleeding adaptors, rubber cup adaptor.

Maximum vacuum: 550mm HG.
Reservoir capacity: 150ml.

Suitable for all types of spark plugs. Finds faults in piston rings, valves, head gaskets and cylinder bores. Suitable for use on most petrol engine vehicles and motorcycles. Can be used on crankshaft seals in two- stroke engines. 195mm flexible hose. For use on 14mm and 18mm threads.


Large easy to read scale 0 - 21bar/0-300psi. Air release valve to allow rapid re-testing.

Valve Spring Compressor


Fully adjustable valve spring compressor for use on large diesel engines. Unique ‘direct action’ compressor lever gives improved visibility and ease of use in areas of difficult access. Manufactured from heavy duty steel with all rivited joints and a slip resistant rubber handle.

• Restricted access adaptors: 25 and 30mm.
• Throat clearance: 250mm.

Valve Spring Compressor

Fully adjustable valve spring compressor for use on multi-valve petrol and diesel engines with deep seated valves. Universal model with unique dual-cam action, parallel lift and automatic locking reversible jaw/adaptor. Unique ‘direct action’ compressor lever gives improved visibility and ease of use in areas of difficult access. Manufactured from heavy duty steel with all rivited joints and a slip-resistant rubber handles.

• Restricted access adaptors: 25 and 30mm.
• Jaw opening: min 55mm, max 175mm.
• Throat clearance: 165mm.

Valve & Piston Ring Compressor


Designed for use on production lines as well as in the automotiveworkshop. Able to cope with occasional commercial use.

Manufactured from bright nickel plated steel with PVC cushion grips.

• Throat depth: 230mm.

Piston Ring Pliers PRP100


To enable fast installation or removal of piston rings. A self-adjusting spring tensioned mechanism manufactured from nickel-plated steel with PVC handles for extra grip. Capacity: 50 - 100mm (2” - 4”).

For supporting and accurately positioning engines during maintenance operations and as an aid for the removal of gearboxes and transmissions. 500kg (1/2 tonne) capacity. Adjustable width to bridge various engine compartments. Fitted with soft rubber feet to protect the bodywork. Supplied with a 92cm long chain. Supporting legs can be tilted.

Ideal for car and light commercial transmission removal and installation. Fully adjustable universal rotary saddle with adjustable corner brackets and safety chains. Foot operated pump and release valve leaves both hands free to manoeuvre transmission. Wide base with four 3” dia. swivel-type ball bearing castors providing stability and easy manoeuvring. Two-stage flash chromed rams inhibit rust from entering the hydraulic system. Lifts from 875mm to 1800mm.

With large cast iron bases with a steel cylinder housing and an adjusting notched saddle. Fitted with an overload protection valve. Two piece ‘pumping’ handle also operates hydraulic release. Use on a firm level surface, do not work under the vehicle until another means of support, such as axle stands, are used.


Models B234, B337 and B541 are supplied in a robust blow moulded carry case.

Strong steel chassis provides stability when under load. Fixed direction castors and swivel castors for easier positioning under vehicles. Long reach single piece pump handle with comfort rubber for rapid raising and lower. Safety overload protection valve prevents overload damage to hydraulic mechanism.


GS and TUV approved.


T238

• Type: with case.
• Dimensions: 525 x 225 x 145mm.
• Maximum load: 2,000kg.
• Minimum height: 130mm.
• Maximum height: 380mm.

T2.249

• Type: with case.
• Dimensions:
• 695 x 344 x 180mm.
• Maximum load: 2,250kg.
• Minimum height: 145mm.
• Maximum height: 495mm.

T280

• Type: long reach.
• Dimensions:
• 1150 x 360 x 210mm.
• Maximum load: 2,000kg.
• Minimum height: 140mm.
• Maximum height: 800mm.

2 in 1 Padded Creeper Board & Seat

Heavy duty steel frame with powder coat finish. Vinyl coated cushioning. Quickly converts from creeper to seat. Adjustable back and parts tray when in the seat position.


Padded Creeper Board

Both the creeper board and seat framework are manufactured from heavy steel with a powder paint finish. Furnished with a vinyl covered cushioning and are fitted with castor wheels for ease of movement.


Padded Creeper Seat

The creeper seat is fitted with a parts tray for tools and components.

Nut Splitters

Mechanical drop forged, hardened and tempered plated steel. Ideal for releasing seized/ damaged nuts etc.


Three Jaw Oil Filter Wrench

For use with ratchet handles, extension bars, flexible drives etc. With 3/8” square drive and hexagon adaptor, or use with 19mm/3/4” AF spanners or sockets. All steel construction, chrome plated with milled teeth on gripping arms for positive action when loosening or tightening.


Oil Filter Pliers

Manufactured from hardened and tempered chrome vanadium with chemically blackened corrosion resistant finish and vinyl grip. Three position rapid jaw adjustment with high grip tooth profile, ensures the minimum amount of effort is required to remove or fit oil filters.

Mechanical Puller - 2 Jaw


Industrial Reversible/Double Ended Adjustable Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications.


Selection

Always use a three jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what ‘spread’ is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.


Mechanical Puller

3 Jaw Industrial Reversible Double Ended Adjustable Manufactured from drop forged chrome vanadium steel.

Circuit Continuity Tester

For testing circuit continuity on non-live systems. Locates broken circuits in fuses, switches, sockets and wires. 1m lead. Super sharp tempered steel probe to test through wire insulation.

Standard Circuit Tester

Suitable for use with power on. For 6 and 12V automotive systems only. Locates shorts, earth and open circuits. 1m lead. Super sharp tempered steel probe to test through wire insulation. Probe length 45mm.

Long Probe Circuit Tester

Suitable for use with power on. For 6 and 12V automotive systems only. Locates shorts, earth and open circuits. 1.7m heavy duty lead with spring strain relief. Super sharp tempered steel probe to test through wire insulation. Extra long probe length: 180mm.

For use on cars and light commercial vehicles. Easy starting with low power loss. Tangle-free copper cable with double insulation. Robust fully insulated colour coded clamps.


Light Duty

Suitable for 12 and 24V systems. 3m cable. 16mm2 multi- stranded cable core rated to 220amps.


Medium Duty

Suitable for 12 and 24V systems. 3.5m cable. 25mm2 multi-stranded cable core rated to 350amps.


Heavy Duty

Suitable for 12 and 24V systems. 4.5m cable. 35mm2 multi-stranded cable core rated to 480amps.

For inflating tyres, airbeds, boats, sports equipment and any other inflatable products. Complete with 3m of cable 12 volt car cigarette lighter plug, nozzles and adaptors. The dual air pressure gauge can be read in both lb/in2 and kg/cm2. 300psi.

Heavy Duty Air Line Tyre Inflator with Gauge

This heavy duty push on inflator is of rugged construction and has a clear view integral pressure gauge reading from 10 - 120psi.

Deluxe Type Tyre Pressure Gauge


In the interests of safety, tyre pressures should be checked at
least once a week when the tyres are cold. This is because the
manufacturers recommended pressures are based on cold tyre
readings. This pressure gauge has a long body, ideal for use on
cars, vans, lorries, plant and equipment etc. It is very robust in construction and has a maximum pressure reading of 120psi.

Pencil Type Tyre Pressure Gauge

This push-on gauge is suitable for cars, vans and light commercials, where readings of up to 120psi are necessary. It is
of chrome plated brass contraction with a pen type pocket clip.


4-Way Tyre Valve Service Tool

This case hardened tool is for the internal and external repair of valve threads, insertion and removal of valve cores.


Tyre Tread Depth Gauge

This handy sized tyre depth gauge is graduated in mm and 1/32”
and comes with a pen type pocket clip.



Specifications :

Manufactured from high quality chrome molybdenum steel. Black oxidized finish with permanent laser etched markings.

Dial Type Tyre Pressure Gauge. In the interests of safety, tyre pressures should be checked at least once a week when the tyres are cold. This is because the manufactures recommended pressures are based on cold tyre readings. This push-on type pressure gauge is graduated in psi and bar up to a maximum of 64psi (4.5bar). The reading is held until the release button is pressed.

Safety equipments, hand gloves, safety jackets, safety halmets, safety belts and safety shoes.

Color coded for easy identification. Can be used withretainer rings or pins.

Contents : 17, 19 and 21mm

Manufactured from chrome alloy steel with a bright nickel and chrome finish. The locking wheel has a black oxidized finish. To use, place the extractor over the stud, then fit any 1/2” square drive handle and turn. The locking wheel moves into place to grip the stud and then remove it. 58mm outside dia. X 65mm high.

 

 

Long Handled Gasket Scraper Set


For cleaning cylinder heads and removing old sealants and carbon build up. Hardened and tempered carbon steel shanks and heads are ‘offset to edge’ to allow easy scraping of flat surfaces. Simple ‘firmer’ style bevelled points with longer head lengths allow for scrapers to be re-ground several times for maximum service life. Impact resistant square section handle for secure grip even when greasy.


Set includes blade widths:

 

• 19mm (3/4”),
• 25mm (1”) and
• 38mm (11/2”).

Overall length:

• 280mm (11")

Standard Length Gasket Scraper Set

Rigid carbon scrapers ideal for cleaning cylinder heads, removing old sealants, carbon build up and a variety of general mutipurpose automotive applications.


Set includes blade lengths:

205mm x 13mm (8” x 1/2”), 205mm x 25mm (8” x 1"), 93mm x 25mm (31/2" x 1”), 97mm x 15mm (33/4” x 5/8”).

For repairing dents in body panels. Supplied complete with self tapping pull screw for use where access to the rear of the panel is blocked by reinforcements or other parts, a range of steel hooks and pull curls for pulling the edges of panels and a chain and hook. The long hammer shaft allows the pulling/striking force to be precisely controlled. 

 

Contents: (1x) hammer (10lbs cast iron), 22.5Ø x 500 and 22.5Ø x 200mm pipes, 2 hole pipes, 6 x 170, 6 x 120, 6 x 200 and 3mm x 100mm plates, chain and hook, hex nut and blow moulded storage case.

Winds back disc brake calipers when replacing brake pads. Professional quality, allows the easy return of brake piston into the caliper. Suitable for most braking systems.

Constructed from heavy gauge steel for heavy duty use with a large diameter saddle for a secure hold under the jacking point. Extra long handle for easy access under bigger vehicles which also tilts and locks in three positions with a built in handle mounted safety release to prevent accidental lowering of the load. A foot pedal pump and fine adjustment are fitted on the handle for optimum vehicle height. Automatic safety overload protection and rear toe plate for easy positioning. GS and TUV approved.

 

 

Used for clamping, pulling, bending, straightening, spreading and lifting operations. Snaps together quickly. Heavy duty hand pump has automatic overload feature. Tough, blow moulded case. Strong flexible hose with spring guards at both ends. Hydraulic hand pump, ram and spreader.

 

 

Spares:

 

 

 

Standard Timing Light


For checking and setting ignition timing on automotive, agricultural and marine engines. For use on 12V systems. Reverse polarity protected. Accurate to 8,000rpm. 135cm long durable power leads. Impact resistant housing. On/off trigger switch. Bright linear Xenon flash tube for daylight use. Focused lens provides concentrated light. Easy to apply inductive impulse pick-up.


Advance Timing Light

For checking and setting ignition timing on automotive, agricultural and marine engines. Measures ignition spark advance from 0-60. For use on 12V systems. Reverse polarity protected. Accurate to 8,000rpm. 1m long removable coiled power leads. Impact resistant metal case and rubber nose cone. On/off trigger switch. Bright linear Xenon flash tube for daylight use. Focused lens provides a concentrated light. Easy to apply inductive impulse pick-up. Built-in check light.

Supplied in a high quality fitted blow moulded impact resistant case. Drop forged, high carbon steel hammers with ground and polished heads and cheeks. Hickory, octagonal section shafts.

• 1x: curved, utility, heel and toe dolly.
• 1x: 12oz shrinking hammer, and flat faced bumping hammer,
• 1x: 10oz round finishing pick.

Made from heavy duty steel with a rubber saddle which provides a positive grip and prevents damage to jacking points. Designed to safely raise vehicles. Easy to use and compact for easy storage. Lifting range: 88 - 383mm. 1 Tonne (1000kg) safe working load. Wide base plate for extra stability.

Base plate size: 150 x 90mm. Spindle thread 12.5 x 2.5mm.

Used for clamping, pulling, bending, straightening, spreading and lifting operations. Snaps together quickly. Heavy duty hand pump has automatic overload feature. Tough, blow moulded case. Strong flexible hose with spring guards at both ends. Hydraulic hand pump, ram and spreader.

Rugged construction with an internal overload valve, a pressure rating of 10,000psi (700bar) and a 1/4 NPT thread size. Operates in a vertical and horizontal position.

Mini Air Compressor commonly known as Pressure Gauge & Tyre Inflator are used for inflating tyres, airbeds, boats, sports equipment and any other inflatable products. Complete with 3m of cable 12 volt car cigarette lighter plug, nozzles and adaptors. The dual air pressure gauge can be read in both lb/in2 and kg/cm2. 300psi.

Panel Seam Splitter Set is ideal for separating spot-welded panels during repairs. Stainless steel coated chrome vanadium with tough tang shafts allow use with hammers. Dual soft grip hammers for comfort and control. Includes 90 degree curved and straight seam splitters. Cushioned handle absorbs any shock from hammer blow. Panel seam splitter set is made from tough alloy steel.

Contents: 3 Pieces Set. 

Brake Fluid Tester is an invaluable in the garage workshop for testing the quality of brake fluid. Testing for moisture contentin the fluid by resistence to electric current. An individual using this will get an instant from the built-in LED indicator light system.
(Runs on 1 x 1.5V AAA battery). 

Padded Creeper Board & Seat is made of heavy duty steel frame with powder coat finish. Vinyl coated cushioning. Quickly converts from creeper to seat. Adjustable back and parts tray when in the seat position.

Size (L x W x H) mm: 1050 x 480 x 100
Weight: 13.0Kg 

Oil Drain Plug Key Set is a comprehensive set of quality 3/8"sq.drive oil drain plug keys with Tommy bar. Made from satin finished chrome vanadium.

Contents: male square 7mm, 8mm(5/16"), 9mm, 3/8", male hex 8, 9, 10, 12, 14, and 17mm
Male triangular 10mm Tommy bar